DESCRIPTION
If you want an easy way to balance your beer lines this is the way to do it. Please be aware that even in the fully open position these FC disconnects do have some inherent flow resistance so you should use either shorter line or larger ID line that you would when compared with traditional ball lock disconnects. One of the benefits of FC disconnects is you don't need to rely on the small ID or line length to apply flow resistance so it would not make sense to use long lines or small ID lines as well as this is the job of the FC device.
This is perfect for people who want to serve a large range of beverages with differing carbonation levels as it gives you the ability to adjust resistance easily. Now with the added benefit of duotight fittings built in.
This particular ball lock disconnect has been designed to suit 8mm Beer Line. Due to the integrated duotight fitting the line will simply push directly into this fitting.
For this ball lock disconnect we recommend using either:
EVABarrier 4mm ID x 8mm OD Line (Best for short draw systems such as our kegerators)
or
EVABarrier 5mm ID x 8mm ID Line
This all new ball lock disconnect sets a new bar! The integrated duotight design means you can connect your beer line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact compared to the previous Stainless Steel Flow Control Ball Lock that has been discontinued due to the difficulty in repeated tooling and overall cost of raw materials.
The flow control ball lock disconnect is made from highly chemical resistant materials with stainless springs and ball bearings - no cheap ABS plastics here - this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitisers and caustics.
Why not a flow control tap/devices?
Flow control devices are good but they inherently can create a small amount of turbulence and therefore can cause foaming. In the past flow control taps have been the only common option. Flow control taps like these ones are popular however they have the issue that due to the fact they are placed right at the end of the beer line they have no head pressure. As a result any turbulence created can cause foaming and carbonation to come out of solution.
Flow control ball lock disconnects like these on the other hand have the ability to restrict the flow before the beer enters the beer line so the head pressure created by the beer line keeps the carbonation in solution. Even in the instance that high turbulence is created the beer will be far more resistant to foaming issues. For this reason flow control ball lock disconnects like these have significantly better performance allowing you the flexibility to adjust line resistance easily but without the introduction of turbulence that creates foaming. It cannot fix over-carbonated beer, but it can reduce the amount of beer line you would need to pour without excessive foaming.
Some of the features include:
- New POK Injection-moulded Design.
Like all new duotights push in fittings that we at KegLand bring to market, all of them are manufactured with polyketone plastic (POK). This aids in chemical resistance, tensile strength, and toughness. - duotight push in
These duotight ball lock disconnects already have the duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done! - Compact
The worlds most compact ball lock disconnect every manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is the only ball lock disconnect that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines. - Overmoulded Poppet
The overmoulded poppet design means you can couple and disconnect this ball lock disconnect under extreme pressures of 150psi and will never have issues with the o-ring blowing out. - Tool-less Disassembly
Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects. - Extreme Chemical Resistance
No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polykeytone resin body, EPDM and PP/EPDM overmoulded poppet. This makes this ball lock disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing. - Toughness
This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor - these bad boys are tough.
duotight Swivel Elbow Sold Separately
If you are often pulling your beer and gas line sideways we recommend the use of the duotight male to female elbow as this allows your gas to swivel 360 degrees without making a kink in the beer/gas line.
KL18456 - 8mm (5/16")
If you are looking to mount this tap directly to your ball lock keg we recommend using this product with these parts sold separately:
KL32179 - Nukatap Mini
KL21418 - Flow Control Ball Lock Disconnect
SHIPPING
Shipping prices are calculated on the checkout page based on the size, weight, and where it needs to be delivered. You can be confident that you will receive accurate and fair shipping rates specifically tailored to suit your individual purchase.
Once an order is placed, please note that KegLand is unable to make changes or additions to the order or modify the shipping information. If any changes are required, it is the customer's responsibility to directly contact the shipping provider and arrange for redirection or any necessary adjustments.
Read More: Shipping Policy